Since the Edition 2 version of the hotend mount uses the larger stock fan, it is able to cool the heatsink more effectively. Both seemed like viable solutions but a little overkill and kludgey. Another option would be to rewire the fan wires to the board so the ground is attached to a different pin and that would run the fan at 100% at all times. It turns out the Prusa Mini firmware runs the hotend fan at 38% speed and there is no way to adjust that speed without modifying the firmware. The fan itself wasn’t to blame, it was a combination of factors. was it my esteps? did I need to PID tune? what was it? So I began to Google… Edition 1 vs Edition 2Īfter Googling and reading forum post after forum post with people experiencing the same issue, I came to the conclusion that the problem was the small fan that comes with the Revo Micro and the Edition 1 mount. I began printing again and the same thing happened again. I reloaded the filament and the filament purged out of the hotend like normal so there was no clog. I unloaded the PLA filament and the extruder had ground down a notch in the filament. Right away on the first layer, the filament started to click and grind in the extruder and nothing was coming out of the hotend. I was sold and ready to order another one for my other Prusa Mini! but I’m glad I waited… Heat Creep IssuesĪfter a few successful PETG prints with the Revo Micro w/Edition 1, I switched over to some PLA filament. The Revo Micro was tiny and cute and I was pleased with the upgrade. Installation was easy enough and I was up and printing with PETG in no time. While printing the Edition 1 mount on another Prusa Mini, I disassembled my hotend and got it prepared for the installation. Afterall, a fan that came with the Revo Micro would surely be better, right?
PRUSA MINI E3D REVO INSTALL
I decided to install Edition 1, since using the old stock fan didn’t seem ideal. There was an ‘Edition 2’ set of instructions, but the only difference I could see was Edition 1 used the fan that came with the Revo Micro, and Edition 2 used the existing stock fan.
PRUSA MINI E3D REVO UPGRADE
Since there was no installation instructions I used the Google and eventually landed on the instructions for the ‘Revo Micro – Prusa Mini upgrade guide (Edition 1)’. However, there was zero documentation in the box, and if I didn’t lift up and look under the box insert I would have easily missed the extension cables. Unboxing the Revo Micro was straight forward. Revo Micro Installation on the Prusa Mini+ Finally! I had a good reason to dip my toes into the Revo ecosystem! I ordered a fully loaded 24v Revo Micro from Printed Solid and patiently waited for it to arrive in the mail. Fast forward to late spring 2022 and I had a failed thermistor on my Mini+. After all, my printers were working just fine….
The biggest feature of course, is being able to quick change a nozzle all while having no leakage between the hotend and the heat break.Īs cool as it looked, I held off and waited to try the new hotend system. It offers a lot of great benefits (with some added cost). We have not tested Revo Prusa Edition with MMU or MMU2, if you are interested in this use case, we have a dedicated discord channel with users who are experimenting with this setup.The E3D Revo RapidChange system was all the buzz late 2021 and quickly sold out everywhere early 2022. Prusa i3 MK2 variants are most often 12V systems and are therefore not compatible with this HotEnd variant.
You may need to adjust your Z offset when changing nozzles. An anodised black heat sink distinguishes Revo Prusa Edition from its predecessor. It reaches temperature much faster than a traditional aluminium heaterblock, and it’s much safer: a positive temperature coefficient (PTC) means the HeaterCore can’t melt at extreme temperatures, reducing hazards in the event of a thermal runaway.Ī new look. Revo Prusa Edition uses a Revo HeaterCore, our latest HotEnd heating and sensing architecture. Each Revo Nozzle is factory sealed, making it much simpler to use and more reliable than most HotEnd technology available today.Įnhanced performance. Revo Prusa Edition is designed to work with Revo Nozzles, so you can perform nozzle swaps with your fingers at room temperature without complex tools or hot tightening. – And yes, you can still use all the print profiles you have built up on Prusa slicer! Just fit it, connect the Revo HeaterCore wires, and you’re ready to 3D print. It has the same height, the same filament diameter, and the same groove mount as the E3D V6, so it drops straight into V6-fitted machines without the hassle of redesigning print head mounts and accessories.
PRUSA MINI E3D REVO UPDATE
Revo Prusa Edition is a top choice if you want to update your old E3D V6 setup to the latest generation of E3D HotEnd technology.
0 kommentar(er)
